New @ CLC!

Boat Plans

Builders' Forum » Chris F's Topics
Builders' Forum \| RSS

Please login or register to post to this forum.

» Night Heron and learning to roll it ?

Chris F on Sat, November 30 2013 » 9:13 AM, 1 Replies

» Following seas, to skeg or not to skeg?

Chris F on Sun, November 3 2013 » 9:48 PM, 11 Replies

» Seat position from bow and center of gravity question?

Chris F on Sun, September 22 2013 » 11:06 PM, 2 Replies

» Anyone recognize this old boat?

Chris F on Mon, September 9 2013 » 7:22 PM, 3 Replies

» Time? Varnish to paddling?

Chris F on Sun, September 1 2013 » 10:37 AM, 2 Replies

» Yearly varnish...how many coats?

Chris F on Thu, June 20 2013 » 4:38 PM, 1 Replies

» CLC Night Heron Finished!

Chris F on Sun, August 19 2012 » 9:51 AM, 5 Replies

» Flush hatches and seal compression...

Chris F on Thu, August 16 2012 » 1:13 PM, 6 Replies

» Using 3m 5200 sealant on bulkheads

Chris F on Wed, August 15 2012 » 7:16 PM, 0 Replies

» Frog painter's paint?

Chris F on Tue, July 10 2012 » 6:10 PM, 0 Replies

» Extra fiberglass after build, where should I reinforce?

Chris F on Thu, July 5 2012 » 2:58 PM, 2 Replies

» What is the best way to get fiberglass tape to end of bow...without making a big mess!

Chris F on Mon, July 2 2012 » 8:16 PM, 6 Replies

» Hatches with fiberglass lip, do I need a seal?

Chris F on Wed, June 20 2012 » 9:21 PM, 2 Replies

» Next step for hatches?

Chris F on Thu, June 14 2012 » 11:05 AM, 0 Replies

» Joint hull with deck or cut hatches first?

Chris F on Mon, June 11 2012 » 8:55 AM, 3 Replies

» How do I get my build ready for winter?

Chris F on Sun, December 11 2011 » 4:59 PM, 2 Replies

» Too much filet around coaming?

Chris F on Fri, November 25 2011 » 7:47 PM, 4 Replies

» Tiny bubbles/dust in epoxy...?

Chris F on Sun, September 4 2011 » 7:42 PM, 3 Replies

» Epxoy sealer coat on hull...

Chris F on Sun, August 28 2011 » 1:34 PM, 5 Replies

» Fiberglass deck before coaming strips?

Chris F on Tue, August 16 2011 » 6:29 PM, 5 Replies

» Do you think my glue has mold?

Chris F on Tue, August 9 2011 » 12:47 PM, 5 Replies

» Signs of Glue after scraping and sanding...

Chris F on Thu, August 4 2011 » 9:29 AM, 6 Replies

» Steaming cedar strips...swelling?

Chris F on Tue, July 26 2011 » 6:24 PM, 1 Replies

» Outer stems...regular carpenters glue or epoxy?

Chris F on Thu, July 7 2011 » 3:12 PM, 4 Replies

» Night Heron Question: Can I make it past the chine without cheaters?

Chris F on Sat, June 4 2011 » 11:41 PM, 7 Replies

» Glue Drying Time for a Strip Night Heron

Chris F on Sat, June 4 2011 » 5:33 PM, 6 Replies

» Strips: to bend or not to bend that is the question?

Chris F on Sat, May 28 2011 » 5:36 PM, 1 Replies

» Sheer line strip and Scarf Joint, which one first?

Chris F on Mon, May 9 2011 » 8:33 PM, 1 Replies

» Night Heron inner stems for bow and stern

Chris F on Sun, May 1 2011 » 7:22 AM, 1 Replies

» Night Heron and CLC kit cut end forms 1, 16, 17, and 17.5

Chris F on Sat, April 30 2011 » 9:42 PM, 3 Replies

» Boat Stands for my Strip-Built Sea Kayak

Chris F on Wed, April 27 2011 » 5:00 PM, 6 Replies

Browse New Arrivals »

Grain Ply-Beam Surfboard Kits

HeadTrip Inflatable Pillow by Eno

Shavehook 3 Piece Set

LowBoy Boat Stand

Builders' Forum » Chris F's Topics

Browse New Arrivals »